1、雙組份打膠機設備應安裝在干燥、無粉塵、無腐蝕性氣體的壞境中，該要求與其他設備一致，當然如果條件達不到至少爭取無腐蝕性氣體，畢竟設備中有電線以及管路這些配件抗腐蝕性不高。
1, the double component glue machine equipment should be installed in the dry, dust free, non corrosive gas, the requirement is consistent with other equipment, of course, if the conditions can not reach at least for corrosion free gas, after all, the equipment with wires and pipelines are not corrosion-resistant.
2、室內溫度好控制在10～40度的室內堅硬地面上，地面應水平度要好。
2, indoor temperature is best controlled in 10~40 degree indoor hard ground, the ground should be better.
3、雙組份打膠機安裝之前，應先檢查是否有因運輸、搬動造成的變形、損壞和緊固件松動情況，之前就曾經有客戶在移動打膠機的過程中把設備的智能控制系統的一個零部件碰掉了而導致設備無法正常運行，我們的工作人員到現場后才排查出的原因。

3. Before the installation of the double component glue machine, we should first check whether there is the deformation, damage and loosening of the fastener due to transportation and moving. Before the client has touched off one part of the equipment's intelligent control system in the process of moving the glue machine, which causes the equipment to be unable to run normally. The reasons for finding out after the scene.
4、我們可以根據地面平整度的實際情況來通過調整設備的可升降地腳螺栓來調整設備的水平度直到設備水平而穩固。然后按圖接線并可靠接地，把氣源接入機器所配帶的氣源接口，確保無漏氣現象。
4. First, we can adjust the level of the equipment to the level of the equipment to the level of the equipment, according to the actual condition of the ground flatness. Then according to the diagram connection and reliable grounding, the air source is connected to the air source interface provided by the machine to ensure that there is no air leakage.
5、雙組份打膠機向油槽中加注液壓油至精選位置，46#液壓油。
5, two component glue machine to the oil tank to add hydraulic oil to the specified location, 46# hydraulic oil.
6、接通電源并打開查看設備是否能夠正常運行。
6, switch on the power and open the viewing device to operate normally.
感謝大家關注公司發布的產品信息，如果你想要了解更多，可以來我們公司咨詢。我們歡迎大家的光臨，并與你的合作!
Thank you for your  to pay attention to the product information released by the company. If you want to know more, you can come to our company for consultation. We welcome everyone's presence and cooperate with you!