1、混膠或沖槍（沖洗混膠器、膠嘴）時，建議把機頭行走到軌道末端，用接膠板接住膠嘴內放出的膠，以免污染設備。
1, when mixing glue or punching gun (Flushing glue mixing machine and rubber nozzle), we must walk the machine head to the end of the track, and use the adhesive plate to catch the glue released from the rubber nozzle, so as not to contaminate the equipment.
2、操作參數設置時，在控制箱pc顯示屏上進行，根據須要而選擇設定值，不要隨意設定，以免控制器發出錯誤的信息，影響打膠質量或損壞設備。
2, when the operation parameter is set, it is carried out on the PC display box of the control box. According to the requirement, the setting value is selected, and it is not set at will, so that the controller can send out the wrong information, affect the quality of glue or damage the equipment.
3、混膠或沖槍時，一定要先打開膠嘴控制閥門，然后再打開供膠機，以免壓力劇增損壞設備或者出現安全事故。
3, when mixing or flushing the gun, we must first open the glue nozzle to control the valve, and then open the machine, so as to avoid the damage to the equipment or the safety accident.
4、打膠時一定要扶好玻璃，避免玻璃脫離定位，影響打膠質量。

4, when the glue is played, the glass must be helped to avoid the glass out of the position and influence the quality of the glue.
5、沖槍時先關閉機頭上的B膠出膠閥門，關閉B膠泵，然后打開B膠回流閥門，后沖槍，沖洗至出膠口不出黑膠，沖洗才能結束。
5, when firing, first close the B glue discharge valve on the machine head, close the B glue pump, then open the B glue reflux valve, and finally flush the gun, rinse to the gel outlet without black glue, and rinse it to finish.
6.機頭電機下面不要有異物，遠離電機以免發生危險。
6. machine head motor under no foreign objects, away from the motor to avoid danger.
7.機頭前方檢測玻璃開關的光眼上不能有膠，否則誤工作。
7. a glass switch in front of the head can not have a glue in the light eye, otherwise the work will be mistaken.
8.膠嘴和兩側的刮膠板如膠多時要清理。
8. the rubber mouth and both sides of the scraper, such as glue, should be cleaned up.
9.吸盤上不能放石灰粉，如有膠請清理，如果有的玻璃邊緣正好放到吸盤的中心時，可調節吸盤左右移動.
There is no lime powder on 9. suction cups. If you have glue, please clean it. If some glass edges are just in the center of the suction cup, you can adjust the sucker to move around.
10.打三玻時要將鋁框檢測探針缷掉，雙玻時在安裝上。
10. hit three glass to the aluminum frame detection probe off off, when the installation of double glass.
公司全方位服務于客戶，以質量上乘、價格合理和的售后服務與客戶攜手奮進，共同發展。質量保證，歡迎咨詢洽談。
The company serves the customer in all directions, with the high quality, the reasonable price and the perfect after sale service and the customers to advance hand in hand, and develop together. Quality assurance, welcome to consult the negotiation.