在運用封膠機時要留意哪些事項：
What should we pay attention to when using sealant machine?
1.混合膠在膠槍內滯留工夫必需控制在3-5分鐘內，否則蜂鳴器報警。
1. Mixed glue must be kept in rubber gun for 3-5 minutes, otherwise buzzer will alarm.
2.封膠之前要反省雙組份膠的混合化，將膠擠到100mm的正方形，厚3mm的浮法玻璃上，再那一塊異樣的浮法玻璃在塊玻璃上一壓，在光亮處反省，如混合膠內有白絲或黑絲，即混合不平均。
2. Before sealing, we should reflect on the mixing of two-component glue, squeeze the glue onto a 100 mm square, 3 mm thick float glass, and then press the unusual float glass on the first glass, and reflect on the bright spot. If there is white or black silk in the glue, the mixing is uneven.
3.要時辰留意液壓設備壓力表（指針指在綠色平安，黃色、白色風險）。
3. Always pay attention to the pressure gauge of hydraulic equipment (pointer refers to green safety, yellow, white risk).
4.留意膠筒壓力表（A組份膠6bar,B組份膠4bar）。
4. Pay attention to the pressure gauge of rubber cylinder (6bar for component A and 4bar for component B).
任務終了后，封閉設備，翻開膠槍，將膠槍內的膠全部擠出壓力小于30bar，如長工夫不必，先將Operatingmade(操作形式開關)打至BASEPURGE(基料沖洗)，再翻開膠槍，直至A組份膠全部擠出，設備封閉，持續打膠直至壓力小于30bar后放入冷凍箱。
At the end of the task, close the equipment, turn over the rubber gun, and extrude all the glue in the glue gun at a pressure less than 30 bar. If it is not necessary for a long time, first hit the Operating Make (operation mode switch) to BASEPURGE (base material flushing), then turn over the glue gun until the A component glue is extruded completely, the equipment is closed, and continue to glue until the pressure is less than 30 bar, then put in. Freezer.
三角形點膠機是依據緊縮空氣送入注射器內，將膠壓入與活塞室相連的進給管中，當活塞處于上沖程時，活塞室中填滿膠，當活塞向下推進滴膠針頭時，膠從針嘴壓出。
The triangle dispenser feeds the rubber into the syringe according to the compressed air. The rubber is pressed into the feed pipe connected with the piston chamber. When the piston is in the upper stroke, the piston chamber is filled with glue. When the piston pushes down the needle, the glue is pressed out from the nozzle.

三角形點膠機在日常任務中能夠會呈現斷膠的狀況看，此時可反省膠水是不是有成績。如膠水中含氣泡或顆粒物，通常此種狀況比擬罕見。點膠控制器也會由于其本身功能或任務中的不正常操作招致斷膠狀況的呈現。
The triangle dispenser can show the situation of breaking glue in daily tasks. At this time, we can reflect whether the glue has achieved good results. If there are bubbles or particulates in the glue, this situation is usually rare. The dispensing controller will also cause the breakage of glue due to its own function or abnormal operation in the task.
UV膠即紫外線固化膠。三角形點膠機廠家引見，若UV膠不出膠，先確定運用黑色的管路。不要間接添加UV膠在壓力筒UV膠上。
UV adhesive is UV curable adhesive. Triangle dispensing machine manufacturers, if the UV glue does not glue, first determine the use of black pipeline. Do not indirectly add UV glue to pressure cylinder UV glue.
應先將原有UV膠放掉，再將UV膠倒入空的壓力筒內，壓力筒內的UV膠往往經過一段工夫后會發生氣泡而形成出膠不波動。
The original UV glue should be released first, and then the UV glue should be poured into the empty pressure cylinder. After a period of time, the UV glue in the pressure cylinder will foam and form the glue without fluctuation.
綜上所述有濟南昌盛機械提供，想了解更多雙組份打膠機知識，歡迎關注我們的網站：http://www.hyjsrq88.com謝謝支持！
In summary, all the above-mentioned Jinan Changsheng Machinery provides, want to know more about the two-component glue machine knowledge, welcome to pay attention to our website: http://www.hyjsrq88.com Thank you for your support!