怎樣調試臥式中空玻璃半自動打膠機放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。首先打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，注意原點設定時避免頭部和輔助吸盤碰撞。

　　How to debug the semi-automatic glue machine for horizontal insulating glass? Place it on a flat and clean surface, connect the power and gas sources, and confirm that they are connected before starting the operation. Firstly, turn on the air pump switch, power main switch, and console switch. Press the manual button on the console, then find the origin setting on the display screen, click on the auxiliary origin setting, and then click on the head origin setting. Be careful to avoid collision between the head and the auxiliary suction cup when setting the origin.

　　等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。然后是混交了，按第一桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，再按鏈接生產線，自動運行，此時可以自動打膠。

　　After setting it up, go back and find the glass thickness setting. First, the thickness of the glass, then the aluminum spacer, and finally the thickness of the glass. After entering it, click on the settings to enter. Wait until the command position matches the current position value, and be careful not to have glass on the conveyor belt during setup. Then it's mixed. Press the first glue button, press the job selection button, and then press the tapping glue start button. After pressing the tapping button, the glue head will release glue. When the white glue is no longer visible, press the tapping button to mix evenly. Then press the link production line, and it will run automatically. At this time, the glue can be automatically applied.

　　調試的注意事項：

　　Precautions for debugging:

　　1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。

　　1. After the machine operation is completed on the same day, the rubber inside the hose should be flushed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the rubber hose and gun with kerosene.

　　2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。

　　2. The silicone or polysulfide glue used in the two-component glue machine should be careful not to have too many impurities. Low quality glue can easily block the filtering system of the rubber hose, causing poor or uneven glue output.

　　3、在更換膠的品種時要非常注意把雙組份打膠機內殘留的膠沖凈，非常好清洗，因?yàn)椴煌贩N甚至品牌的膠容易反應堵塞機器。4、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安全事故。

　　3. When changing the type of glue, special attention should be paid to flushing out the residual glue in the two-component glue machine, and it is best to clean it, because different types or even brands of glue are prone to reacting and blocking the machine. 4. The pressure of the hydraulic station system cannot be adjusted too high. It should be adjusted according to the actual indoor environment temperature and other conditions to meet the normal and uniform dispensing of glue from the nozzle. When opening the hydraulic station, be sure to turn on the glue gun, otherwise the pressure in the B component pipeline will rise very high, causing a safety accident.

　　本文由 中空玻璃打膠機 友情奉獻.更多有關的知識請點擊  http://www.hyjsrq88.com/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the insulating glass gluing machine For more related knowledge, please click http://www.hyjsrq88.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.