雙組份打膠機的常見問題及處理方法

　　Common problems and solutions of two-component gluing machines

        一、膠水混合不均勻

　　1、 Uneven mixing of glue

　　雙組份打膠機的膠水由兩種不同的液體混合而成，如果混合不均勻，就會導致打出的膠水質量不穩定。該問題的主要原因是兩種液體的比例不對或者膠水在混合過程中被污染。解決方法是檢查混合比例是否正確，清洗膠水加料口以及膠嘴等部位。

　　The glue of the two-component glue machine is made by mixing two different liquids. If the mixing is not uniform, it will lead to unstable quality of the glue produced. The main reason for this problem is the incorrect ratio of the two liquids or contamination of the glue during the mixing process. The solution is to check if the mixing ratio is correct, clean the glue feeding port and the glue nozzle.

　　二、膠水流量不穩定

　　2、 Unstable glue flow rate

　　膠水流量不穩定是雙組份打膠機常見的問題之一，可能是由于膠水中氣泡過多、液壓系統不完善或者膠嘴損壞等原因引起的。首先，檢查膠水中的氣泡是否完全排出，其次，檢查液壓系統是否運作正常，非常是是否存在泄漏情況，非常后，檢查膠嘴是否損壞。

　　Unstable glue flow rate is one of the common problems in two-component glue machines, which may be caused by excessive bubbles in the glue, incomplete hydraulic system, or damage to the glue nozzle. Firstly, check if the bubbles in the glue have been completely removed. Secondly, check if the hydraulic system is functioning properly, especially if there are any leaks. Finally, check if the glue nozzle is damaged.

　　三、膠水無法正常噴出

　　3、 Glue cannot be sprayed out normally

　　如果膠水無法正常噴出，可能是由于打膠機的空氣壓力不足、膠嘴堵塞或者液壓系統出現故障等原因引起的。解決方法是檢查空氣壓力是否合適，清洗膠嘴或更換膠嘴，還可以檢查液壓系統是否有故障。

　　If the glue cannot be sprayed normally, it may be caused by insufficient air pressure of the glue machine, clogged glue nozzle, or hydraulic system malfunction. The solution is to check if the air pressure is appropriate, clean or replace the nozzle, and also check if there is a malfunction in the hydraulic system.

　　四、膠水泡性、氣泡過多

　　4、 Adhesive foaming, excessive bubbles

　　雙組份打膠機打膠的質量直接影響產品的質量，如果膠水中含有大量氣泡，就會導致膠水質量下降。該問題的主要原因是打膠機的壓力不足、膠水中含有過多的氣體或者管路中有空氣等。解決方法可以提高打膠機的壓力或排除氣體，清洗管路中的空氣。

　　The quality of the two-component glue machine directly affects the quality of the product. If there are a large number of bubbles in the glue, it will lead to a decrease in the quality of the glue. The main reasons for this problem are insufficient pressure on the glue machine, excessive gas in the glue, or air in the pipeline. The solution can be to increase the pressure of the glue machine or eliminate gas, and clean the air in the pipeline.

　　五、液壓系統壓力低

　　5、 Low hydraulic system pressure

　　如果雙組份打膠機的液壓系統壓力低，將影響膠水的流量和穩定性。該問題的主要原因是液壓系統中的油泵失效或油液污染等。解決方法是更換油泵或者清洗油液，確保液壓系統正常工作。

　　If the hydraulic system pressure of the two-component glue machine is low, it will affect the flow rate and stability of the glue. The main cause of this problem is the failure of the oil pump or oil contamination in the hydraulic system. The solution is to replace the oil pump or clean the oil to ensure the normal operation of the hydraulic system.

　　本文由雙組份打膠機提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.hyjsrq88.com，我們將會全心全意為您提供滿意的服務。

　　This article is supported by a two-component gluing machine. For more detailed and exciting content, please click on our website http://www.hyjsrq88.com We will wholeheartedly provide you with satisfactory service.