1、雙組份打膠機打膠之前注意觀察打膠機的膠頭是否有玻璃參差等異物出現，如果將其摻入密封膠內那么我們的中空玻璃的密封效果肯定就不會有那么好了。

　　1, before the glue, pay attention to observe the glue head of the glue machine, whether there is glass uneven and other foreign bodies appear, if it is mixed into sealant, then the sealing effect of our insulating glass will certainly not be so good.

　　2、打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，我們將打膠機膠頭讓他回位到原點，這是我們要對打膠機的速度進行下調節(一般情況下使用我們設置好的速度即可)，密封不嚴可能是由于打膠機的打膠速度過快而我們的鋁條安裝的時候深淺不一所以導致中空玻璃的密封膠在鋁條深的地方會出現密封不嚴的情況。

　　2, open the pump switch, power switch, control switch, manual button on the console, we will glue machine glue head let him return to the origin, this is we want to fight the glue machine speed regulation (we use set speed under normal circumstances can), may be sealed and lax the glue machine glue fast and our aluminum strips when installing shades resulting in insulating glass sealant in aluminum deep place will be sealed and lax circumstance.

　　3、然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，此時我們就可以進行正常的打膠機工作了。

　　3, then is mixed, according to the first barrel of plastic button, and then press the select button according to the work, take glue start in cutting, the rubber head to glue, such as invisible glue, to mix well after the press cutting off, we can carry out normal atx-ii work at this time.

　　4、出現中空玻璃打膠機生產出來的中空玻璃密封不好的另一大主要原因就是我們的鋁條安裝過于隨意~~~盡管我們的設備無需進行設置可全自動的檢測并處理深淺不一的鋁條，但是如果差距太大且打膠速度過快的話也是有可能發生中空玻璃密封不嚴漏氣的情況。

　　4, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum strip is installed too freely while our equipment ~ ~ ~ without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.

　　5、打膠機的供嬌壓力如果不夠的話也是會出現這個問題的，因為打膠機的膠體完全靠氣壓來擠出設備并巧妙的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴

　　5, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass. If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict

　　本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://www.hyjsrq88.com謝謝您的到來

　　The wonderful content of this article comes from the two component dispenser, please click on our official website: http://www.hyjsrq88.com, thank you for coming