1、固化速度太快或太慢

　　1, curing speed is too fast or too slow

　　2、雙組份打膠機混合不勻，出現白絲，花膠

　　2, two-component glue mixing is not uniform, white silk, fish maw

　?、俅蚰z機混合器單向閥泄漏，更換單向閥。

　　Rubber mixer, mixer one-way valve leakage, replace one-way valve.

　?、诖蚰z機混合器及槍內通道部分堵塞，清洗混合器和管道。

　　The glue mixer, mixer and gun passages are blocked, and the mixer and pipe are cleaned.

　?、鄞蚰z機比例泵內有臟物，清洗比例泵。

　　There is dirt in proportion pump and cleaning proportion pump.

　?、芸諌簷C空氣壓力不足，氣量不穩，調整壓力。

　　The air pressure of the air compressor is not enough, the air volume is unstable, and the pressure is adjusted.

　　3、打膠機壓盤冒膠

　　3, glue machine, pressure plate gel

　?、賶罕P密封圈損壞變形，老化發硬，更換新的膠圈。

　　The sealing ring of pressure plate is damaged, deformed, aged and hard to be replaced, and new rubber ring is replaced.

　?、谏祲毫μ?。

　　The lifting pressure is too great.

　?、弁疤罅?，不合適，客戶在采購時，先量一下自己的打膠機壓盤大小，現在市面上機器壓盤有三個規格的，560mm，565mm，571mm,暖萬佳科技開發有限公司可以跟據客戶的機器壓盤大小，提供相應的包裝桶包裝。

　　The barrel is too big, not appropriate, customers in the procurement, the first volume of your gum machine platen size, now on the market of machine platen three specifications, 560mm, 565mm, 571mm, warm Wanjia science and technology development limited company can according to customer's machine platen size, provide the corresponding packaging barrels packaging.

　　4、中空玻璃安裝，經冷、熱交換起霧的問題

　　4, the installation of insulating glass, cold and heat exchange fog

　?、匐p組份硅酮膠主要是二道密封，粘結結構的作用，所以頭道密封建議用丁基密封膠密封，插角處用丁基膠密封完全。

　　The two-component silicone rubber is mainly two sealing, bonding structure, so the seal must be sealed with butyl sealant, inserted at the corner completely sealed with butyl rubber.

　?、诟邷?、高濕季節，建議用質量較好的分子篩，完全能夠將玻璃密封后殘存的濕氣吸干凈，以絕后患。整個操作時間不能太久。

　　In the season of high temperature and high humidity, must use the better quality of the molecular sieve can be completely sealed after the remaining moisture glass suction clean, with all. The whole operation shouldn't take long.

　　5、膠盤壓不下去

　　5, rubber disc pressure can not go down

　　①桶變形，不圓了，可用錘子把桶口拷圓，再壓下去。

　　The barrel deformation, not round, available hammer bungholes copy circle, press down.

　　②桶太小了，或是壓盤密封圈過大，可以在密封圈上涂抹一點白膠，可起到潤滑的作用再壓下去。

　　The barrel is too small, or the pressure plate sealing ring is too large, you can smear a little glue on the sealing ring, can play the role of lubrication pressure.

　　6、氣泡問題(A組份有氣泡或是混合后出現氣泡)

　　6, bubble problem (A group has bubbles or bubbles after mixing)

　?、賶耗z時未能完全排盡空氣，所以每次換膠時，一定要把排空氣的閥門打開，等空氣排完后再關上。

　　Pressure glue can not completely exhaust the air, so every time you change glue, you must open the exhaust valve, and then close the air after the completion of the switch.

　?、谑謩踊炷z過程中混入空氣。

　　Mixing air in manual mixing process.

　　本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://www.hyjsrq88.com/謝謝您的到來!

　　The exciting content of this article comes from the two component dispenser, please click on our official website: http://www.hyjsrq88.com/, thank you for coming!