放在一個平整干凈的平面上，連接電源和氣源，兩者確認接通之后就開始進行操作。
Put it on a flat and clean surface, connect the power supply and the air source, and start the operation after they are confirmed to be connected.
打開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯示屏上找到原 點設定，點擊輔助原 點設定，然后點擊頭部原 點設定，注意原 點設定時避免頭部和輔助吸盤碰撞。
First, turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid the collision between the head and the auxiliary suction cup when setting the origin.
等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值一致即可，注意設置時傳送帶上不要有玻璃。
After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum bar, and then the glass thickness. After entering, click set to enter. Wait until the command position is consistent with the current position. Pay attention not to have glass on the conveyor belt when setting.
然后是混交了，按一桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混均勻以后按伐關，再按鏈接生產線，自動運行，此時可以自動打膠。
Then there is mixing. Press the button of a bucket of glue, press the work selection button, and then press the button of beating glue to start. When pressing cut open, the glue will come out of the glue head. When the white glue can not be seen, press cut close after mixing, and then press the link production line to run automatically. At this time, the glue can be filled automatically.

調試的注意事項：
Matters needing attention in debugging:
1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the operation of the machine on the same day, the glue in the hose should be flushed out to prevent hardening; If it is not practical for a long time, pay attention to clean the hose and gun with kerosene.
2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統(tǒng)，造成出膠不暢或不均勻。
2. For the silicone glue or polysulfide glue used in the two-component rubber beater, attention should be paid to that the impurities should not be too high. The low-quality glue is easy to block the filter system of the hose, resulting in poor or uneven glue delivery.
3、在更換膠的品種時要非常注意把雙組份打膠機內殘留的膠沖凈，清洗，因為不同品種甚至的膠容易反應堵塞機器。
3. When changing the type of glue, special attention should be paid to rinse and clean the residual glue in the two-component gluing machine, because different varieties or even brands of glue are easy to react and block the machine.
4、液壓站系統(tǒng)的壓力，不能調的太高，要根據室內環(huán)境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安 全事故。
4. The pressure of the hydraulic station system can not be adjusted too high. According to the indoor environment temperature and other actual conditions, the pressure should be adjusted to meet the requirements of the normal glue output of the rubber nozzle and the uniform glue injection. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, causing safety accidents.