大小片中空玻璃打膠難？雙組份打膠機，告別殘膠返工，效率翻倍

　　Is it difficult to glue large and small pieces of insulating glass? Two component gluing machine, bidding farewell to residual glue rework, doubling efficiency

　　在中空玻璃深加工行業，尤其是大小片異型、大尺寸中空玻璃生產，打膠封邊一直是行業共性難題：手工打膠不僅效率低下，還出彩易出現溢膠、殘膠、邊角不飽滿、密封不均等問題，后續還要貼美紋紙、用壁紙刀裁切、人工清理殘膠，耗時耗力，成品合格率低，嚴重影響交付效率與企業利潤。針對這一痛點，定制款雙組份打膠機憑借合理控膠、快捷穩定的優勢，有效顛覆傳統手工打膠模式，成為玻璃加工廠降本增效、提升品質的核心設備。

　　In the deep processing industry of insulating glass, especially in the production of large and small-sized irregular and large-sized insulating glass, gluing and sealing edges has always been a common problem in the industry: manual gluing is not only inefficient, but also prone to problems such as overflow, residue, incomplete edges and corners, uneven sealing, and subsequent pasting of decorative paper, cutting with wallpaper knives, and manual cleaning of residue, which is time-consuming and labor-intensive, with low product qualification rate, seriously affecting delivery efficiency and enterprise profits. In response to this pain point, the customized two-component gluing machine, with its advantages of precise glue control, high efficiency and stability, completely subverts the traditional manual gluing mode and becomes the core equipment for glass processing plants to reduce costs, increase efficiency and improve quality.

　　傳統手工打膠：工序繁瑣，殘膠通病難根治

　　Traditional manual gluing: The process is cumbersome, and the common problem of residual glue is difficult to cure

　　以往大小片中空玻璃手工打膠，流程出彩為繁瑣：打膠前建議先貼美紋紙防護，避免膠水溢出污染玻璃；打膠過程中全靠人工把控出膠量與均勻度，大尺寸玻璃操作難度出眾，邊角、接縫處出彩易出現缺膠、氣泡；打膠完成后，需用壁紙刀劃開美紋紙，再手動啃除殘膠，即便反復清理，玻璃表面仍會殘留膠漬，影響外觀整潔度。

　　In the past, the process of manually gluing large and small pieces of insulating glass was extremely complicated: before gluing, it was necessary to apply masking paper for protection to prevent glue from overflowing and contaminating the glass; During the gluing process, the amount and uniformity of glue are all manually controlled. It is extremely difficult to operate large-sized glass, and there is a high risk of missing glue and bubbles at corners and seams; After gluing, it is necessary to use a wallpaper knife to cut open the decorative paper, and then manually remove the remaining glue. Even after repeated cleaning, there will still be glue stains on the glass surface, which will affect the appearance cleanliness.

　　這種模式不僅工序多、勞動強度大，單塊玻璃打膠+清理耗時優于10分鐘，人工成本居高不下，而且成品質量完全依賴工人手藝，密封性能無法保障，后期易出現漏氣、滲水問題，返工率常年居高不下，尤其面對批量訂單，產能與質量很難兼顧，成為制約玻璃加工廠發展的瓶頸。

　　This mode not only involves multiple processes and high labor intensity, but also takes more than 10 minutes to glue and clean a single piece of glass, resulting in high labor costs. Moreover, the quality of the finished product relies entirely on the craftsmanship of workers, and the sealing performance cannot be guaranteed. In the later stage, there is a high risk of air leakage and water leakage, and the rework rate remains high all year round. Especially in the face of bulk orders, it is difficult to balance production capacity and quality, which has become a bottleneck restricting the development of glass processing plants.

　　雙組份打膠機：合理控膠，一次成型無殘膠

　　Two component glue machine: precise control of glue, one-time molding without residual glue

　　針對大小片中空玻璃定制研發的雙組份打膠機，從根源解決手工打膠痛點，實現封邊作業自動化、標準化。設備采用合理雙組份配比供膠系統，確保膠水混合均勻，出膠量穩定可控，針對大尺寸、異型玻璃可靈活調節出膠速度與膠層厚度，適配各類規格中空玻璃加工，無需提前粘貼美紋紙，打膠過程中無溢膠、無拉絲，玻璃表面干凈整潔，有效省去后續殘膠清理工序。

　　A two-component gluing machine customized and developed for large and small pieces of insulating glass, which solves the pain points of manual gluing from the root and achieves automation and standardization of edge sealing operations. The equipment adopts a precise two-component ratio glue supply system to ensure uniform glue mixing and stable and controllable glue output. For large-sized and irregular glass, the glue output speed and glue layer thickness can be flexibly adjusted to adapt to various specifications of hollow glass processing. There is no need to paste decorative paper in advance, and there is no overflow or drawing during the gluing process. The glass surface is clean and tidy, completely eliminating the need for subsequent residual glue cleaning processes.

　　實地調試案例顯示，廣東佛山某玻璃加工廠啟用該定制款設備后，打膠效果肉眼可見提升：玻璃邊角封膠飽滿順滑，接縫處無氣泡、無斷層，外立面無明顯膠漬殘留，成品合格率接近100%；單塊玻璃打膠時間縮短至3分鐘內，產能較手工模式提升3倍以上，無需額外人工清理，大幅降低人工成本與返工損耗，設備操作簡單，調試完成后即可穩定運行，工人上手快，無需依賴資深技工。

　　Field debugging cases have shown that after a glass processing factory in Foshan, Guangdong Province started using this customized equipment, the adhesive effect was visibly improved: the glass edges and corners were sealed with full and smooth adhesive, there were no bubbles or faults at the joints, and there were no adhesive residue on the exterior facade. The finished product qualification rate was close to 100%; The bonding time for a single piece of glass has been shortened to less than 3 minutes, and the production capacity has increased by more than 3 times compared to manual mode. There is no need for additional manual cleaning, greatly reducing labor costs and rework losses. The equipment is easy to operate and can run stably after debugging. Workers can quickly get started without relying on experienced technicians.

　　核心優勢與行業適配性

　　Core advantages and industry adaptability

　　雙組份打膠機不僅適用于大小片中空玻璃，還可適配常規中空玻璃、幕墻玻璃等多種產品，膠層厚度可控制在3-8mm標準區間，密封性能符合行業規范，防水、抗老化、密封性優于手工打膠。設備運行穩定，維護簡便，針對玻璃廠批量生產需求，可實現連續作業，大幅縮短訂單交付周期，提升企業市場競爭力。

　　The two-component sealant applicator is not only suitable for large and small pieces of insulating glass, but also for conventional insulating glass, curtain wall glass and other products. The thickness of the adhesive layer can be controlled within the 3-8mm standard range. The sealing performance meets the industry specifications, and the waterproof, anti-aging and sealing performance is far superior to manual sealant applicator. The equipment runs stably and is easy to maintain. In response to the batch production needs of glass factories, it can achieve continuous operation, greatly shorten the order delivery cycle, and enhance the market competitiveness of enterprises.

　　對于玻璃深加工企業而言，手工打膠的時代已然過去，雙組份打膠機憑借快捷、高質、低成本的優勢，成為行業升級必備設備。告別繁瑣的手工清理，告別殘膠返工困擾，一次打膠成型，既提升產品顏值，又保障密封質量，真正實現產能與品質雙提升，助力企業輕松應對各類中空玻璃訂單，快捷交付、安心回款。

　　For glass deep processing enterprises, the era of manual gluing is over, and two-component gluing machines have become essential equipment for industry upgrading due to their advantages of high efficiency, high quality, and low cost. Say goodbye to tedious manual cleaning and the trouble of reworking residual glue. One shot molding not only improves product appearance but also ensures sealing quality, truly achieving dual improvement of production capacity and quality, helping enterprises easily cope with various hollow glass orders, efficient delivery, and secure payment.

　　本文由  雙組份打膠機  友情奉獻.更多有關的知識請點擊  http://www.hyjsrq88.com/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a two-component glue machine For more related knowledge, please click http://www.hyjsrq88.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.